Exploring HUB75

I bought some "HUB75" displays which are quite interesting because they do not self-refresh, instead you have to constantly drive each LED with the desired value, and as the LEDs are only "1-bit" (meaning that they can be on or off) you can't just set a specific color (eg: blue to 187).

However, these panels have a high refresh rate, so we can emulate color depth by quickly toggling the right LEDs on and off.

What we consider normal colors are usually represented in 3 channels, R, G and B, each channel with an 8-bit range. The color white is represented as #ffffff, which is 255 (0xff) on all three channels.

In the same fashion that white can be split into three channels, we can split each channel into a bit plane; paraphrasing Wikipedia, a bit plane is a set of bits corresponding to a given bit position in each of the binary numbers representing the signal.

If we take the green channel as an example (only 4 bits for easier representation)

Each bit-plane must be displayed for different lengths of time, otherwise the pattern 1100 and 0011 would be visible as the same color.

To represent these bit-planes according to the color we'd expect, we can display each bit for twice as long as the previous one and let our eyes do the "integration" of the image brightness.

In this case we'd be displaying the MSB for 8 "periods", the next one for 4, then 2, then 1.

Displaying brightness this way is called binary coded modulation or BCM.

Another example, representing a color with multiple channels as bitplanes over time:

Here, this Magenta (#d80073) is only composed of the red and blue channels, so the green channel always stays off.

Taking the 4 most-significant-bits of each channel, we have R = 0b1100 (0xd) and B = 0b0111 (0x7)

The basic operation of the display:

• Select the current row with the pins A, B, C, D
• Place the corresponding bit for the R1, G1 and B1 channels on the input, then shift it into the display by bringing CLK up and down
• When the current row is complete, bring LATCH up and down

This lets you display an entire row of data. Repeat this with different values for A/B/C/D and you can shift in an entire bit plane.

In this case, we are shifting the 3 (R, G, B) bitplanes at once; on top of that, these displays usually populate two rows in parallel: [row index] and [row index + 16]; the second row is fed (R2, G2, B2).

For a given color depth D, we need to shift in 2^D bitplanes, which are composed of R rows and C columns.

Taking my display as an example (64 columns, 32 rows) and a 4 bit depth image, we would need to clock in 2⁴ * 64 * 32 = 32768 pixels

Going to 5 bit depth doubles the pixels per frame to 65536 and 6 bit to 131072.

As the protocol does not rely on a fixed clock, we can shift data in as fast/slow as we want, which leaves a lot of room to bit-bang the protocol

We can manipulate each pin individually, as an example (code):

if element.r1 > 0 {
    self.pins.r1().set_high()?;
} else {
    self.pins.r1().set_low()?;
}
if element.g1 > 0 {
    self.pins.g1().set_high()?;
} else {
    self.pins.g1().set_low()?;
}
// ...
self.pins._clk.set_low()?;
self.pins._clk.set_high()?;

Displaying a 5-bit image this way takes 116ms, which is very visibly flickering - each row is only being driven 1/16th of the total time, so each row is on for 7 ms, then off for 109ms.

Some simple optimizations:

• Increasing clock speed from 160MHz to 240MHz by setting CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ_240=y results in a 77ms frame time
• Optimizing build by setting lto = true in Cargo.toml results in a 67ms frame time

The ESP32 supports setting/clearing the lower 32 pins (0..=31) in one memory write:

fn fast_pin_set(pins: u32) {
    unsafe { core::ptr::write_volatile(GPIO_OUT_W1TS_REG as *mut _, pins); }
}
fn fast_pin_clear(pins: u32) {
    unsafe { core::ptr::write_volatile(GPIO_OUT_W1TC_REG as *mut _, pins); }
}

where each bit in pins marks which bit will be set/cleared, as an example; calling fast_pin_set(0b00000000000000000000000000010101) will set the pins [0, 2, 4].

Knowing that, we can remove the branching & individual pin writes on the hot loop:

let rgb = (r1 >> 5)
    | (g1 >> 2)
    | (b1 << 1)
    | (r2 << 15)
    | (g2 << 18)
    | (b2 << 21);
let not_rgb = !rgb & rgb_mask;
fast_pin_clear(not_rgb);
fast_pin_set(rgb & rgb_mask);
self.pins._clk.set_low();
self.pins._clk.set_high();

Now the time per frame is down to 25ms, which is a huge improvement, but still flickery.

We can also include clock in the batch set/clear, as this is executed 65k times per frame:

let rgb = (r1 >> 5)
    | (g1 >> 2)
    | (b1 << 1)
    | (r2 << 15)
    | (g2 << 18)
    | (b2 << 21);
let not_rgb = !rgb & rgb_mask;
fast_pin_clear(not_rgb | (1 << clkpin));
fast_pin_set((rgb & rgb_mask) | (1 << clkpin));

This brings the time down to 4.8ms (!!)

While we no longer have any branches in the hot loop, we are still doing 6 bit shifts, which can be avoided.

Ideally, we could pre-format the data to not require any shifts, something like pixels = XXRGB_RGB, then write the lower 6 bits straight to the W1T register; however the ESP32 does not really expose 6 contiguous pins that can be written to.

The ESP32 does have multiple groups of 3 pins which only have 1 gap, and this can be useful, as we only need to shift out 6 bits of data per pixel.

The groups I picked for RGB1 and RGB2 are [2, 4, 5] and [18, 19, 21].

By packing the pixel data as pixel = R1__G1B1R2G2__B2, the only computations needed in the inner loop are 2 shifts and 2 masks:

let rgb1 = *element as u32 & 0b1101_0000;
let rgb2 = *element as u32 & 0b0000_1011;
// The base of RGB1 is at pin 2
let pixdata: u32 = rgb1 >> 2;
// The base of RGB2 is at pin 18
let pixdata = pixdata | (rgb2 << 18) | (1 << clkpin);

This gives another 20% improvement, bringing the time per frame down to 3.95ms.

This is with 6 bit color depth, each frame takes 7.9ms to render

I wanted a higher resolution for a project, 128x64, which 4 times as much as the numbers we were working with so far; on a 6-bit depth that means each frame takes 32ms to render, which very visibly flickers.

Lowering the color depth to 5 bit halves the time per frame to 16ms which looks smooth if you are stationary, but if you move it definitely looks 'off'.

I didn't want to figure out how to get the I2S peripheral on the ESP32 to work as I needed, I thought it'd be super frustrating, so instead I wrote a PIO program for the Raspberry Pi Pico.

To drive the screen in its most basic way, I used two state machines and fed them from the ARM core. I have some ideas on how to use 4 state machines and DMA to not use the ARM core at all, but this project's taken long enough already.

The first state machine drives the data & clock pins:

.wrap_target
    ; Auto-pull blocks & shifts 32 bits into OSR

    in osr, 8        [0] side 0 ; 8 lowest OSR bits into ISR (xxRGBRGB)
    out null, 8      [0] side 0 ; shift 8 zeroes into OSR
    mov pins, isr    [1] side 1 ; col 0 & clock posedge

    in osr, 8        [0] side 0 ;
    out null, 8      [0] side 0 ; shift 8 zeroes into OSR
    mov pins, isr    [1] side 1 ; col 1 & clock posedge

    in osr, 8        [0] side 0 ;
    out null, 8      [0] side 0 ; shift 8 zeroes into OSR
    mov pins, isr    [1] side 1 ; col 2 & clock posedge

    in osr, 8        [0] side 0 ;
    out null, 8      [0] side 0 ; shift 8 zeroes into OSR
    mov pins, isr    [1] side 1 ; col 3 & clock posedge

.wrap

The second state machine drives the 5 address pins, along with the latch and OE pins (copied from the example implementation):

.wrap_target
    ; Auto-pull blocks & shifts 32 bits into OSR

    out pins, 5 [2]    side 0b00 ; oe=1; latch=0
    out x, 27   [2]    side 0b11 ; oe=1; latch=1
pulse_loop:
    jmp x-- pulse_loop side 0b00 ; oe=0; latch=0
.wrap

The two state machines synchronize thanks to having auto-pull enabled, which will block reads from the OSR if there's no data.

With PIO, a 6-bit, 128x64 image can be rendered in 1.8ms, about 17x faster than the bit-banged ESP32 implementation.

This is also about the limit on the display anyway, as rising the clock on the PIO causes ghosting on the images.